Bass Boat Chine Walking - iboats Boating Forums
2012年9月16日 · Re: Bass Boat Chine Walking Jim, trim tabs don't help in this situation because the boat is designed to be up on the pad surface and the chines have very little contact with the water. When it falls of the pad the chine dips and the boat steers itself in one direction or the other depending on where the load difference is.
What is Chine? | Boating Forum - iboats Boating Forums
2003年11月24日 · A round bottom boat can have a hard chine or a soft chine depending on the angle of the bottom rise to the sides and radius of the "roll" at the chine. Both chine shapes affect the roll motion of a boat as well, either with a 'soft' chine or a 'hard' chine. The lower the angle of deadrise the harder the chine in general terms.
What is Chine Walking? | Boating Forum - iboats Boating Forums
2005年4月4日 · what is chine walk? <br /> mostly scary above 70 MPH or so.<br /> more so if your the passenger and know what is going on.<br /> the chine is the area of the bottom that meets the sides. when its rocking off the pad side to side it hits and rebounds to the other side. can lead to loss of control and the occasional barnacle side up situation.
One chine sitting on trailer roller - iboats Boating Forums
2007年12月31日 · Hey guys, I have a 19' Sea Pro WA, and when I pulled it out of the water this winter, one of the chine's towards the front of the boat was sitting in the center of one roller, because the roller is misaligned. I was going to jack the boat off …
Repairing damaged chine/ stringer. - iboats Boating Forums
2008年4月5日 · The chine had a crack through the center of it, horizontally, for about 20" that was allowing water to enter the hull while underway. I've removed the damaged area, revealing a little bit of rot to the stringer underneath.
Starcraft Chine Issues | Boating Forum - iboats Boating Forums
2010年6月7日 · My 18'SS has cracks at the rib rivet heads nearest the chine seam. Shows up worst on port side. Near the middle of the boat, at about 4-5 ribs, we have the cracking in the hull. Cracks run fore-aft each about 1.5" total length. I figure it is the hull flexing and the chine being quite stiff concentrates a stress just in from teh chine.
Air Assist Chine? | Boating Forum - iboats Boating Forums
2009年10月29日 · Hey folks, As I've said before in many of my jovial posts, I just purchased an 08 Monterey 180FS. Monterey is apparently very proud of this 'Air Assist Chine' business, which is a hull shape, right around the plane area, which directs some air under the boat and is …
Jacking the Boat Up (can't believe this worked)
2012年6月10日 · With the boat on a trailer, the chine is a better place to lift from a safety standpoint, as the chine traps the board/pads. Lifting at the keel is a real balancing act . . . and at the stringers, you are lifting more weight with poorer access and less support for the jacks. The use of a long board really distributes the load nicely along the ...
Great video on Chine Walking (triton bass boat) | Boating Forum ...
2006年9月17日 · Chine walk is the tendency of the boat to rock back and forth (side to side) on the "pad". The pad is the flat portion of that hull just ahead of the transom. It is accentuated by prop torque and engine height. It can also be caused by loose or soft engine mounts. Getting a boat to "dance" on the prop alone is tricky, at best.
Crack ACROSS chine - pictures & Video - iboats Boating Forums
2008年6月30日 · Re: Crack ACROSS chine - pictures Clean and prep the area real good and go the Marine Tex route. It will definately be strong enough and should last you a long time.