Aeotec Multisensor 6 on Batteries (motion sensor issues)
2019年12月31日 · I just wasted another 2 hours trying to switch back to using batteries. I think there's an Aeotec firmware bug that prevents the sensor from reporting motion OFF (Base Set value=0x00 instead of 0xFF) when running on batteries. Aeotec was reporting every 4 minutes Basic Set = 0xFF (motion detected) even tough it was sitting in the room by itself.
Issues with Aeotec Home Energy Monitor GEN5 - Universal …
2021年8月10日 · Good morning all, I'm trying setup a simple program to monitor my sump pump. I did not want to plug something inline with the pump, so I took a short power cord, stripped away the outer insulation and am trying to use the Aeotec …
Please add support for Aeotec ZW095 (Gen 5 HEM)
2017年5月30日 · Yes, I thought this was about the "Aeon Labs Home Energy Meter(2nd Edition)" but your topic title is clearly stating "Aeotec ZW095 (Gen 5 HEM)". I'm sorry for the confusion. The older model has this explanation for parameter 2: "If the reverse clamping pliers, negative power is detected. (0==disable,1==enable)". OK!
Aeotec MultiSensor 7 - Home Center 3 - Smart Home Forum by …
2022年4月8日 · The MS7 came with 1.3 firmware. on the Aeotec site the latest firmware it says is V1.03 which im assuming its the same. The HC3 is on latest beta 5.102 Saying that when i had it on stable 5.100 i did manage to add and was configured and motion detection was intermittent, however now on the beta its always adding as Not Configured..
Aeotec Zwave Device - Smart Home Forum by FIBARO
2022年2月12日 · Aeotec TriSensor is updated via OTA also did the "reconfigure device" under "Device Configuration" tab but still the same result. Also there is a software update for the gateway (Version: 5.100.22) is this version safe?
Aeotec Home Energy Meter - Other Devices / Third-party devices
2021年5月27日 · But if your supply from the energy company is 3 phases (most probably the case), purchase a 3 phase Aeotec HEM meter " Aeotec Home Energy Meter Gen5 – xxxA with three clamps"; please check your main breaker amperage if is less than 60A, then is 60A is OK, if is more than 60A, you should go for the higher amperage Aeotec meter ; i.e. 100A ...
Schlage 469 Locks, Aeotec Gen5, 6 repeaters Z-Wave issues
2021年1月28日 · The ISY is right next to one of the locks and that one appears to communicate fine. The other 2, not so much. I do have 1 Aeotec Gen6 repeater and two Aeotec Gen5 repeaters, one GE Enbrighten motion switch and a GE On/Off module to assist with communications, but they don't seem to be helping much.
Pairing Aeotec Home Energy meter Gen 5 with HC3
2023年2月11日 · Unable to pair Single phase 60 amp Aeotec Home Energy meter Gen 5 with Fibaro HC3 ( Software version 5.130.64 ) HC3 Detects and starts the pairing process, but it fails during configuration. The sequence of messages on the HC3 are as follows:- - Requesting Neighbours - Multiple devices added ( Green backed messages appear and disappear)
Aeotec Siren Gen 6 - Smart Home Forum by FIBARO
2019年12月4日 · Sadly Aeotec dont provide volume parameter for older gateways. It whould be so easy instead of doing it by newer command class which HC2 doesnt have. To make the best of it, you can choose a much quiter tone for your purpose: I created a VD similar to above. In addition it provides changing tones for "browse" device (there are 30 build in tones).
AEOTEC Home Energy Meter && FIBARO Incompatibility(ies)
2023年8月18日 · -Update the aeotec gen5 energy meter to the lastest firmware. Last year this was firmware 1.6. In order to get that, you need to open a support ticket on the aeotec website. -Update the gen5 engergy meter with the firmware you got from aeotec. I did this with a Zwave Gen5 Stick from aeotec. -Include the gen5 energy meter to hc3 again.